April 04, 2025, 08:17:39 PM
|
 Show Posts
|
|
Pages: [1]
|
|
2
|
Online Help Center / Software for DNC and CNC / regular expressions and 888 pogram
|
on: September 02, 2011, 11:36:51 PM
|
|
I have got my fanuc O-T controller to communicate both ways manually and can send a file from fanuc to pc in server mode and put it in the right place. But i need to know how to format my 8888 program to get files from the server. My O-T has no option to use brackets
|
|
|
|
|
3
|
Online Help Center / Software for DNC and CNC / Re: uart receiver parity error
|
on: July 18, 2011, 12:43:06 AM
|
|
Sorry wrote error wrong
UART Receiver framing error
paste from log file
2 18/07/11 09:41:58 [Mazak - 6G] Ready!
2 18/07/11 09:41:58 [Mazak - 6G] Waiting for the start of a file
1 18/07/11 09:42:02 [Mazak - 6G] UART receiver framing error
2 18/07/11 09:42:02 [Mazak - 6G] Ready!
2 18/07/11 09:42:02 [Mazak - 6G] Waiting for the end of a file
1 18/07/11 09:42:02 [Mazak - 6G] UART receiver framing error
1 18/07/11 09:42:02 [Mazak - 6G] UART receiver framing error
1 18/07/11 09:42:02 [Mazak - 6G] UART receiver framing error
1 18/07/11 09:42:02 [Mazak - 6G] UART receiver framing error
1 18/07/11 09:42:02 [Mazak - 6G] UART receiver framing error
1 18/07/11 09:42:02 [Mazak - 6G] UART receiver framing error
1 18/07/11 09:42:02 [Mazak - 6G] UART receiver framing error
1 18/07/11 09:42:02 [Mazak - 6G] UART receiver framing error
1 18/07/11 09:42:03 [Mazak - 6G] UART receiver framing error
1 18/07/11 09:42:03 [Mazak - 6G] UART receiver framing error
2 18/07/11 09:42:03 [Mazak - 6G] Ready!
2 18/07/11 09:42:03 [Mazak - 6G] The file has been successfully received
2 18/07/11 09:42:03 [Mazak - 6G] Saving data to file [C:\CNC Programs\Mazak 6G\Recieve\0133.TXT]
|
|
|
|
|
4
|
Online Help Center / Software for DNC and CNC / uart receiver parity error
|
on: July 16, 2011, 01:18:10 AM
|
|
Machine to pc
Mazak 6g with Mazatrol EIA dash controller.
I am receiving the files to the PC ok but I get the above error at the begining of the transmission.
Mazak coms settings
Code ISO
Stop bits 2
Check parity even
Parity check off
baud rate 4800
Settings in software
7 bits
no parity chech
2 stopbits
4800 baud
Is this a problem i need to fix
|
|
|
|
|
5
|
Online Help Center / Software for DNC and CNC / Re: Server Recieving file from Fanuc OT
|
on: January 10, 2013, 11:00:00 AM
|
|
Also is this normal
The status line on the bottom is cycling through these things every 5 seconds
Waiting NC commands
Waiting NC commands
Waiting for the transmitter ready
Ready!
Waiting for the start of the file
and then in red
Can't receive a sigh of the start of a file
And round it goes again,
|
|
|
|
|
6
|
Online Help Center / Software for DNC and CNC / Server Recieving file from Fanuc OT
|
on: September 25, 2010, 12:42:36 AM
|
|
Hello
I have a machine with a FANUC OT controller. I cannot use brackets as that option on this machine is not turned on.
when i send a file from the NC to the PC the PC responds but then hangs with the message along the bottom.
Waiting for end of file.
Please what am i missing
Malcolm
|
|
|
|
|
Loading...
|
Show Posts